Clutch Kit Opel Astra H Combo Corsa C Meriva 1.7 CDTi Z17DT | Flywheel Conversion from Bimass to Single Mass Flywheel | 93182242

Product Description:

Clutch Kit SRLine Opel Astra H Combo Corsa C Meriva A | 1.7 CDTi Engine Type Z17DT | Z17DTH | Conversion from Dual Mass Flywheel to Rigid Flywheel | Clutch Disc Pressure Plate and Single Mass Flywheel | OE 616065 | 616231 | 55564465 | 93182242

This clutch kit with flywheel has been developed to replace the original clutch with dual mass flywheel. This simplified, but extremely robust design differs in its external appearance from the original clutch. Instead of a dual mass flywheel with a rigid clutch disc, a rigid flywheel and a disc with a high performance torsional damping system is used.

Part no:

63090821

Similar OEM part number:

SCKE-OP34R | HKF1063 | DMV264M | LKCA670024F | 11228229 | 616065 | 616231 | 55564465 | 93182242 | 2294501175 | 415025610 | 600016600 | 828437 | 835074 | 845074 |

Mounting Side:

Front

Compatible Models:

OPEL

ASTRA H (A04) de | 2003 | 2004 | 2005 | 2006 | 2007 |  

ASTRA H (A04) de | 2007 | 2008 | 2009 | 2010 | 2011 | 2012 | 

COMBO C (X01) de | 2000 | 2001 | 2002 | 2003 |  

COMBO C (X01) de | 2003 | 2004 | 2005 | 2006 | 2007 | 2008 | 2009 | 2010 | 

CORSA C (X01) de | 2000 | 2001 | 2002 | 2003 |  

CORSA C (X01) de | 2003 | 2004 | 2005 | 2006 | 

MERIVA A (X03) de | 2003 | 2004 | 2005 | 2006 | 

MERIVA A (X03) de | 2006 | 2007 | 2008 | 2009 | 2010 | 

Other Specifications:

No. of teeth: 14

Hub profile: 25,21 x 22,1

Clutch assembly procedure:

Before fitting the new clutch disc, it is important to check its axial runout. This may be max. 0.5 mm. Higher values can cause dragging.

Afterwards, the splined hub of the clutch disc and the primary shaft of the transmission must be lightly greased all around with high-performance grease (temperature-resistant and able to withstand high surface loads). Now, the clutch disc will be able to move easily back and forth along the primary drive shaft and the excess grease must be removed from both the splined hub and the primary drive shaft.

After all, if too much grease is used, centrifugal forces will carry it to the friction linings of the clutch disc during operation. Coatings contaminated in this way will cause jerking or slipping of the clutch during driving.

It is possible to physically mount the clutch in both positions, but it is important to know that only one of the positions is correct. Even sometimes by mounting the disc upside down, the vehicle may appear to operate correctly in the short to medium term.

This is not real, as incorrect mounting will eventually lead to mechanical problems in the vehicle, and may even cause the disc itself or the thrust bearing to break.

It is very important to respect the correct position of the clutch disc to avoid mechanical damage.

To do this, the easiest way is to locate the word on the clutch discs that indicates its position;

Getriebe Seite Gearbox Side
Gearbox Side Gearbox Side
TM-Side Gearbox side
Motor Side Motor side
Motor Side Motor side
Schwungrad Seite Lado motor
Flywheel Side Lado motor
Flywheel Side Engine side

Warranty:

1 Year Warranty Against Manufacturing Defect.

The images of our products may vary according to the manufacturer, maintaining all the technical characteristics and compatibilities indicated in the product specifications.