Ring | Steering Wheel Contact | Airbag Spiral Spring Dacia Logan I | Sandero I | Duster I | Renault Clio II | OE 255670657R

Product Description:

Ring:

Steering Wheel Contact | Spiral Spring Airbag Dacia Logan I Steering Wheel Contact | Spiral Spring Airbag Dacia Logan I | Sandero I | Duster I | Renault Clio II | OE 255670657R

Part No:

T430867

Similar OEM Part No:

25 56 706 57R | 255670657R | 34446405 | 251779 | V46-72-0223 | CCC71006AS |

Mounting Side:

Steering Rod

Compatible Models:

LOGAN (SD) de | 2004 | 2005 | 2006 | 2007 | 2008 | 2009 

LOGAN (SD) de | 2009 | 2010 | 2011 | 2012 | 2013 | 

DUSTER (HS_) de 2010 | 2011 |2012 | 2013 | 

DUSTER (HS_) de | 2013 | 2014 | 2015 | 2016 | 2017 | 

SANDERO (SD) de | 2008 | 2009 | 2010 | 2011 | 2012 | 2013 | 

CLIO II (BB|CB) de | 1998 | 1999 | 2000 | 2001 | 

CLIO II (BB|CB) de | 2001 | 2002 | 2003 | 2004 | 2005 | 2006 | 2007 | 2008 | 2009 | 2010 | 2011 | 2012 | 

DACIA

Logan I (LS) desde 09-2004

Logan I MCV (KS) desde 02-2007

Logan I Express (FS) desde 2009

Logan I Pick-up (US) desde 03-2008

Duster SUV de 04-2010 a 01-2018

Sandero I (SD) desde 06-2008

RENAULT

Clio II Hatchback (BB, CB) de 09-1998 a 12-2016

Other Specifications:

2 Connections to 2-Pin Steering Wheel Airbag (Yellow Connector | Grey Connector)

1 Connection to 2-Pin Vehicle Installation + 1 Connection to 2-Pin Vehicle Installation with Terminal

Check compatibility with original part number and attachments below

THIS ELECTRICAL PART IS WITHOUT WARRANTY AND RETURN

ASSEMBLY INSTRUCTIONS

It is necessary to refer to the vehicle workshop manual to carry out the specialised service operations for this part.

If the service manual is not available or if you do not have the necessary skills to install this part, it is recommended that you call in a specialised technician.

Read and follow all instructions carefully and heed all warnings and cautions in the vehicle manual.

Airbag systems are subject to the explosives legislation in force in each country. The following safety instructions must be observed when handling them:

-Stop the engine, disconnect the battery and wait for the electronic calculator memory to be cleared (at least 10 minutes). Start the engine and check that the instrument panel does not light up.

-Disconnect the airbag module before any intervention on the vehicle's electrical circuit (ohmmeter, measuring instruments, etc.).

-Handle the airbag modules with care (avoid knocks, keep the opening space free and store the airbag modules upwards)

-Never disassemble the module or connect a measuring device to the module itself.

Installation and removal of the airbag ring must be carried out in the central position (tyre direction must be in the straight-ahead position) and the steering wheel in the fully centred position.

The ring is supplied in the centre position and secured with a pin, the pin must be released after fitting, releasing the spring.

The spring must not be released before fitting under any circumstances, otherwise, if released before fitting, the spring will be distorted beforehand and is very likely to become detached during the operation and become unusable.

If recentering is required, follow the instructions below (valid for most references):

Turn the rotor counterclockwise (left) as far as it will go. Turn the rotor approximately 3.0 turns clockwise (right) until the rotor marks are aligned.

Spiral cable

The spiral cable represents the connection between the rigid steering column and the movable steering wheel. It ensures communication between the airbag control unit and the gas generator during the rotational movement of the steering wheel. The conductive foil is wound in such a way that it is able to follow the rotational movement of 2.5 turns in each direction.

It is important to be very careful when assembling or disassembling this spiral cable. It must be ensured that the steering is in the central position and that the wheels are also straight. If the spiral cable has been dismantled, it cannot be rewound.

The images of our products may vary according to the manufacturer, while maintaining all the technical characteristics and compatibilities indicated in the product specifications.