Clutch Kit FORD Focus I | Tourneo Transit Connect 1.8 TDCi | Conversion to Rigid Flywheel | OE 1S416477DB 1S416477DG

Product Description:

Clutch Kit SRLine FORD Focus I | Tourneo Transit Connect 1.8 TDCi | Conversion from Dual Mass Flywheel to Rigid Flywheel | Clutch Disc Pressure Plate and Single Mass Flywheel | OE 1S416477DB | 1S416477DG

This clutch kit with flywheel has been developed to replace the original clutch with dual mass flywheel. This simplified, but extremely robust design differs in its external appearance from the original clutch. Instead of a dual mass flywheel with a rigid clutch disc, a rigid flywheel and disc with high performance torsional damping system is used.

Part no:

30290820

Similar OEM part number:

98-FO-FO01M | HKF1011 | 1131858 | 1151412 | 1328841 | 1351187 | 1426558 | 1566973 | 1S416477DB | 1S416477DG | 1S41-6477-AB | 1S416477DF | 1S416477DE | 1S416477AB | 1S416477DD | 1S416477DC | KV-FO01M | 98FO01M | KC084 | DMV199M-CSC | LKCA640040F | 415018510 | 600004400 | 2294501068 | 2290601026 | 826883 | 835019 | 845019 |

Mounting Side:

Front

Compatible Models:

FOCUS (DAW|DBW|DNW|DFW) de | 1998 | 1999 | 2000 | 2001 | 2002 | 2003 | 2004 | 

TOURNEO | TRANSIT CONNECT (C170) de | 2003 | 2004 | 2005 | 2006 |  

TOURNEO | TRANSIT CONNECT (C170) de | 2006 | 2007 | 2008 | 2009 |  

TOURNEO | TRANSIT CONNECT (C170) de | 2009 | 2010 | 2011 | 2012 | 2013 | 

Other Specifications:

No. of teeth: 23

Clutch assembly procedure:

Before fitting the new clutch disc, it is important to check its axial runout. This may be max. 0.5 mm. Higher values may cause dragging.

Afterwards, the splined hub of the clutch disc and the primary shaft of the transmission must be lightly greased all around with high-performance grease (temperature-resistant and able to withstand high surface loads). Now, the clutch disc will be able to move easily back and forth along the primary drive shaft and the excess grease must be removed from both the splined hub and the primary drive shaft.

After all, if too much grease is used, centrifugal forces will carry it to the friction linings of the clutch disc during operation. Coatings contaminated in this way will cause jerking or slipping of the clutch during driving.

It is possible to physically mount the clutch in both positions, but it is important to know that only one of the positions is correct. Even sometimes by mounting the disc upside down, the vehicle may appear to operate correctly in the short to medium term.

This is not real, as incorrect mounting will eventually lead to mechanical problems in the vehicle, and may even cause the disc itself or the thrust bearing to break.

It is very important to respect the correct position of the clutch disc to avoid mechanical damage.

To do this, the easiest way is to locate the word on the clutch discs that indicates its position;

Getriebe Seite Gearbox Side
Gearbox Side Gearbox Side
TM-Side Gearbox side
Motor Side Motor side
Motor Side Motor side
Schwungrad Seite Lado motor
Flywheel Side Lado motor
Flywheel Side Engine side

Warranty:

1 Year Warranty Against Manufacturing Defect.

The images of our products may vary according to the manufacturer, maintaining all the technical characteristics and compatibilities indicated in the product specifications.