Lambda sensor Nissan | Renault | Infiniti | 4 Pin Connector | Front or Rear Mounting | OEM Similar to 22693-JA00B

Product Description:

Nissan | Renault | Infiniti | Grey 4 Pin Square Connector | Rear or Front Mount depending on model | OEM Similar to 22693-JA00B

Voltage: 12v
Mounting Side: Front | Rear (depending on model)
Recommended Replacement Interval: 100,000 miles (160,000 km)
Terminal Type: Black 4 Pin Square Connector | Check model as this may vary depending on vehicle | Fit Plug Connection if applicable
M18x1.5
Cable Length: 300 mm

Compatible Models:

NISSAN

Navara (D40) 2.5 dCi 4WD de 12-2009 a 01-2010 | 2488 cc 140 kw 190 cv | Tipo de Motor YD25DDTi
Navara (D40) 2.5 dCi de 07-2005 a 01-2010 | 2488 cc 106 kw 144 cv | Tipo de Motor YD25DDTi
Navara (D40) 2.5 dCi 4WD de 07-2005 a 01-2010 | 2488 cc 128 kw 174 cv | Tipo de Motor YD25DDTi
Navara (D40) 2.5 dCi 4WD de 10-2008 a 01-2010 | 2488 cc 106 kw 144 cv | Tipo de Motor YD25DDTi
Navara (D40) 2.5 dCi 4WD de 10-2006 a 01-2010 | 2488 cc 126 kw 171 cv | Tipo de Motor YD25DDTi

Pathfinder (R51) 2.5 dCi 4WD de 01-2005 a 01-2010 | 2488 cc 120 cc 163 cv | Tipo de Motor YD25DDTi
Pathfinder (R51) 2.5 dCi 4WD de 10-2006 a 01-2010 | 2488 cc 126 cc 171 cv | Tipo de Motor YD25DDTi
Pathfinder (R51) 2.5 dCi 4WD de 03-2005 a 01-2010 | 2488 cc 128 cc 174 cv | Tipo de Motor YD25DDTi

X-Trail (T31) 2.5 4X4 de 06-2007 a 07-2010 | 2488 cc 124 cc 169 cv | Tipo de Motor QR25DE

RENAULT

Koleos (HY0C|HY0N) 2.5 4x4 de 09-2008 a 2015 | 2488 cc 126 kw 171 cv | Tipo de Motor 2TR 700 | 2TR 702 | 2TR 703
Koleos (HY0C|HY0N) 2.5 de 09-2008 a 2015 | 2488 cc 126 kw 171 cv | Tipo de Motor 2TR 700 | 2TR 702 | 2TR 703

INFINITI

35 X (VQ35HR) de 2007 | Tipo 228 310

Reference:

SL1034

Similar OEM part number:

22693-JA00B | 226A3-ES60A | 22693JA00B | 226A3ES60A | 22693 JA00B | 226A3 ES60A | 211200-7040 | 234-9073 | 2112007040 | 2349073 | 211200 7040 | 234 9073

Mounting Side:

Mounting Side: Front | Rear (depending on model).

Compatible Models:


Other Specifications:

Voltage: 12v
Recommended Replacement Interval: 100,000 miles (160,000 km)
Terminal Type: Black 4 Pin Square Connector | Check model as this may vary depending on vehicle | Adapt Plug Connection if applicable
M18x1.5
Cable Length:

Warranty:

1 Year Warranty against manufacturing defect.

The images of our products may vary depending on the manufacturer, maintaining all the technical characteristics and compatibilities indicated in the product specifications. Our company is associated to Fremm (Regional Federation of Metal Entrepreneurs of Murcia) and is part of the Association of Automobile Spare Parts Dealers of the Region of Murcia (ACRAREM).

Check the installation and use specifications according to the manufacturer's instructions.

With the use of a Lambda sensor in perfect condition, we will be sure to have:

Less pollution.

Better engine operation and performance.

Lower fuel consumption (Lambda sensors in poor condition can cause up to a 15% increase in fuel consumption).

No damage to the catalytic converter.

Check the correct functioning of the Oxygen Sensor at least every 30,000 km.

By means of the lambda sensor signal, the control unit recognises the composition of the mixture. The lambda sensor monitors the fuel-air mixture ratio and ensures that the engine operates at the optimum mixture, which is Lambda 1.

In over-fuelled or rich mixtures (Lambda <1), fuel injection is reduced, while in under-fuelled or lean mixtures (Lambda >1), the amount of fuel injected is increased until the optimum is reached.

It is recommended that after a major crash the Lambda sensors be checked or replaced.

The following steps must be followed to install the Oxygen Sensor:

    Before installing the Oxygen Sensor, ensure that you are using the appropriate part number for your vehicle.

    Do not install the Oxygen Sensor if it has been knocked.

    Disconnect the battery. Disconnect the connector from the Oxygen Sensor to be replaced (the one located on the vehicle).

    Remove the lambda sensor from the vehicle, making sure to leave enough cable for splicing if necessary.

    Then, if it is a universal sensor, cut the wires from the removed lambda sensor, thus separating the connector from the rest of the lambda sensor.

    Remove the insulation, according to the length indicated, taking care not to damage the metal core of the cable.

    Insert the stripped wires from the connector into the bushings fitted to the new Oxygen Sensor, taking care to respect the colours of the wires.

    Flatten the sleeves. Apply heat to the heat-shrink sleeve on the bushing to ensure that the connection between the recovered connector and the new sensor is correctly fixed and watertight.

Once the process described above has been completed, you can install the lambda sensor in your vehicle.

To check the correct operation of a lambda sensor, without removing it from the vehicle, we need an oscilloscope.

Bearing in mind that the engine must be adjusted within the manufacturer's specifications, we proceed to warm up the engine.

Connect, by means of the appropriate and specific connection system, the sensor output to the oscilloscope input, always without disconnecting the Lambda sensor from the car's ECU. Once these connections have been made, keep the engine at around 2,000rpm. Under these conditions, if the Lambda sensor is working correctly, the signal shown on the oscilloscope will vary rapidly and constantly between 0.2 volts (lean mixture) and 0.8 volts (rich mixture).

Another very important fact that must be taken into account is the time taken to change from one voltage to another, which should be about 300 milliseconds.

The time taken to switch from lean to rich and from rich to lean should be the same or very similar. If the signal generated by the sensor is constant or the reaction time to the change in richness of the mixture is too slow, the lambda sensor must be replaced. It is advisable to check the operation of the lambda sensor every time the engine is adjusted and always before emissions testing. Remember that slow lambda sensor operation directly affects the vehicle's fuel consumption, so the cost of replacing the lambda sensor will be quickly amortised.